Page 4 of 41

Canon 5d Mk II Manual


Canon 6d Manual


Canon T6 Manual


Canon T5i Manual


Canon T2i


Canon T3i Manual



Building Chemistry Instruments with Arduino

During the fall 2016 semester we worked with Professor Amy Witter in her Destroy Build Destroy chemistry course where students learned to build their own ‘citizen science’ versions of chemistry analysis devices using ardunio boards. Here is an article written on our website about the project with a related video. 

Dickinson Makes

Dickinson Makes Spring 2017 Make and Take Workshop Series

Dickinson Makes


3D Printing : Fall 2016 Recap

This semester our 3D printers were running daily to produce projects for a few different courses. The largest project came out of the Introduction to Sculpture course taught by Professor Amy Boone-McCreesh. The students were tasked with designing a file that had two simple requirements. It had to incorporate both a hook and a hole. This would allow the prints to connect to one another in countless ways much like the old barrel full of monkeys chains.

Professor Boone-McCreesh prototyped her own example file (see orange and clear prints below) to give her students an idea of where to start.  Brenda Landis then led one training session where the students were taught to use the online 3D modeling program, Tinkercad. They worked for about an hour prototyping and modifying their designs and sent the files over for test prints within 2 days. There were 6 students in the course and out of the initial test run 3 came out ready for more duplication, 1 needed minor tweaking and 2 needed extensive modification. After just a few days the files were able to be stabilized for mass production. The project goal was to print 20 copies of each file for an installation in the Writing Center (you can go check out the installation for yourself!).

The files were small enough to fit between 7 and 15 prints on the bed each time so after a week of printing daily, we had enough for the install. After reflecting on the experience we realized that some files ended up being larger than others but that also made them more stable and less likely to break when they were dropped so possibly increasing the scale would help with long term stability of the files.  The final installation files were printed in clear filament which was a help because the files could easily be repaired with hot glue that blended with the material perfectly so imperfections were not very noticeable.

More requests for prints came in as the semester progressed including a few from Professor Marcus Key’s Natural History Mosaic students. A (glow in the dark!) dinosaur skull and trilobite were printed off of files available on Thingiverse.

A student in an Environmental Studies course came to us late in the semester and wanted to print this mountain terrain for use in a presentation.

Professor Hans Pfister in Physics toured the Makery earlier this semester and was eager to chat to about the uses our 3D printer might provide in his work.  He recently read about the work Math Professor, Dave Richeson, has done on creating impossible cylinders. They are based on Sugihara’s Circle/Square Optical Illusion that is a 3-dimensional shape that looks like a circular cylinder but in a mirror looks like a square cylinder. Professor Pfister wondered if we could print a prototype from Professor Richeson’s work and in just a day Professor Richeson sent over an exported file and we printed a copy for both of them. We love it when a plan comes together.

You can download your own copy of the file on Thingiverse and this is the description of the file with blog posts and journal articles written by Professor Richeson included.

This is a 3D file based on Sugihara’s Circle/Square Optical Illusion. Kokichi Sugihara created the video “Ambiguous Optical Illusion: Rectangles and Circles.”
In it he shows a 3-dimensional shape that looks like a circular cylinder but in a mirror looks like a square cylinder.
The 3D file was created by Mathematics Professor, Dave Richeson, at Dickinson College. He has blogged about the project and has shared a pdf file that can be printed and cut to replicate the illusion. He also wrote an article about the illusion in the September 2016 issue of the journal Math Horizons.

Geogebra file and description

Canon 5D

Full-Frame SLR Training Resources

In order to have access to The Media Center’s 5d and 6d full-frame SLR cameras, one must pass a technical quiz. This quiz covers the basic technique that you would learn in an introductory photography class. If you are self taught, you can reference the articles below.

In order to pass the quiz you must get all the questions correct. It is “open book” and you can research answers that you initially get wrong.

You must take the quiz at The Media Center during business hours (M-F 8-5) . Either Josh, Brenda or Julie will grade the quiz and give instant feedback.

The following topics will be included:


shutter speed


focal length

setting the video settings


If you would like to schedule an appointment to speak about your projects or get some technical advice you can also reach out to Julie to addresses your ideas/ concerns:


Here are some readings to help you succeed passing the quiz



This article outlines the components of shooting manually in a very basic way.


How to Use Manual Mode to Make Artistic Choices for Your Photography


This article gives a bit more technical information about the same concepts:


Camera Exposure: Aperture, ISO & Shutter Speed


This article outlines the basic concepts of focal length:


4 Things You Should Know About Focal Length and Composition


Understanding video settings:




This series of video lectures gives an extremely in depth look at the technical aspects of digital photography (not necessary for the quiz):



Page 4 of 41

Powered by WordPress & Theme by Anders Norén